AmiensFixed hydraulic pressure for lifting platformPotential development

The normally closed valve is dirty; The solution is to remove the normally closed valve and use detergent or cleaning.

0The oil filter is seriously blocked; The solution is to clean the oil filter or replace the hydraulic oil.

qAmiensBefore using the safety helmet， adjust the safety helmet liner of the safety helmet， and keep a certain space between the safety helmet liner and the safety helmet shell.

Generally， and tighten it if it is loose. The tightness of the connecting bolts of the engine body shall be checked when the engine body is under pressure. All connecting shafts must have cotter pins and shall be fully expanded.

DMalamboHow to install and use the bearings of the elevator in the process of the bearing device of the elevator? We can not ensure that the bearing device is in the right position every time. It is inevitable that some devices are not in place or the bearings are offset. Once these problems occur in the device， the clearance between the bearings will become too small， and then the inner and outer rings of the bearings cannot be in the same rotation center. Therefore，Hydraulic elevator when installing bearings，TaiyuanFactory hydraulic lifting platformThe price of continues to rise it is necessary to use special things， and it is also necessary to use a detector to test the bearing device in the future， so as to ensure the success of the bearing device.

NvIt is necessary to frequently check the water accumulation and humidity of aerial work vehicles driving in rainy and snowy weather or through muddy roads. The bottom and some gaps and the indoor floor are easy to collect sludge. If the owner does not wash in time， this will make the water hidden. Therefore the outer edge of the wheel hub， the door， the bottom corner of the tree trunk， the key hole and the wiper holder and other activities in other areas should be checked regularly， and the drainage holes of the door and all parts of the body should be kept unblocked to ensure that the car seat covers， such as humidity，Hydraulic elevator carpets and floors， prevent rust parts.

Any machinery needs to be maintained after use， I will tell you how to maintain the lift after use. In order to maintain the good technical state of the lift machinery， ensure the safe use of the construction machinery on site， extend the service life of the equipment， and reduce the mechanical failure， all construction enterprises must maintain according to the relevant provisions Necessary equipment maintenance shall be carried out according to the maintenance regulationsMaintenance. It is strictly forbidden to take out of warranty and repair of equipment.

Precautions for use of guideway elevator Precautions for use of guideway elevator: overloading and transporting flammable and explosive products are strictly prohibited.

sIn the process of mechanical development of guide rail elevator， in order to ensure the use of the lifting platform under safe conditions and keep in touch with relevant rules and regulations， the vehicle body shall be grounded as required. The climbing operation of the lifting platform shall be commanded by the operator who shall communicate with the lifting platform operator according to the standard signal. The announcement signal should be clear and accurate. Guide rail elevator is safe and convenient to use. Generally， lift the lower arm first，Hydraulic elevator then the middle arm， and then the upper arm. During the inverted operation of the lifting platform the lower arm must be inverted after lifting at a certain height. The inversion reaction is slow. Pay attention to whether the spacing between the shear arm and the platform meets the safety requirements of each equipment.

MGenerally，TaiyuanFactory hydraulic lifting platformThe price of continues to rise check the connection of each part and tighten it if it is loose. The tightness of the connecting bolts of the engine body shall be checked when the engine body is under pressure. All connecting shafts must have cotter pins and shall be fully expanded.

AhowLarge logistics warehousing equipment service company with guaranteed price and guaranteed service. Since the fixed elevator is a mechanical equipment， the quality and performance of the product are good. Do not accept the temptation of some manufacturers to buy products with substandard quality， so as to avoid some potential safety hazards in use.

oEIn case of overheating of the motor during the daily maintenance of the elevator， park the car immediately， remove the obstacles， and then continue to run. The motor bearing should be smooth and excellent.

Different power modes can be selected according to different requirements， such as three-phase AC power supply， single-phase AC power supply，Hydraulic elevator_ Cargo elevator_ Cargo elevator_ Hydraulic lift - goods lift manufacturer DC power supply and internal combustion power supply. With manual hydraulic equipment， the lifting operation can be carried out in places with power failure or without power supply， and components can be added. When the platform length is short， it can be extended to the required direction， and then the operation power can be increased. It is the necessary equipment product of modern huge construction and equipment， and it is necessary for safe and civilized production at high altitude.

: The rust of spiral elevator is caused by the fact that some manufacturers materials are not stainless steel. If the rust is not serious， sandpaper can be used to polish the rust.

new productrThe anti-rust work of aerial work vehicles is generally something that needs attention when aerial work vehicles have not been used for a long time. How should we protect the body of aerial work vehicles from corrosion? In fact， it is very simple to go to the maintenance station for anti-corrosion， as long as our car owners can use some materials they can find， and pay attention to the driving habits to ensure that the aerial work vehicle does not rust. Here are some points for reference.

DThe overall structure is intact. Check whether the overall structure is deformed and whether the important parts are damaged， especially the load-bearing support rods and chains.

Now elevators have been widely used in many industries. The spiral elevator is no exception， and has a very good effect. However， sometimes the surface of the spiral elevator will rust， which will have a certain impact on the work efficiency and need to be removed. So what is the solution to the rust on the surface of the spiral elevator?

aAmiensThe lifting table does not lift when the voltage is too low. Check the starter potential when the motor is working with load. Allowable hydraulic range of voltage± % of the motor does not rotate. Check whether the motor and circuit motor are reversed and arbitrarily change the two phases in the three-phase line.

fGThe anti-rust work of aerial work vehicles is generally something that needs attention when aerial work vehicles have not been used for a long time. How should we protect the body of aerial work vehicles from corrosion? In fact， it is very simple to go to the maintenance station for anti-corrosion， as long as our car owners can use some materials they can find， and pay attention to the driving habits to ensure that the aerial work vehicle does not rust. Here are some points for reference.

Precautions for elevator installation: keep the access road of external construction elevator smooth and have enough space for parking equipment. When the auxiliary installation of the crane is required， full consideration shall be given to whether the site environment meets the operating conditions of the crane.