CasetaHydraulic automatic lifting platformExcellent quality

There will be electric brushes in this machine. The parts where the brushes touch each other must be kept clean. The bearings in the machine also need to be checked regularly， especially the bearings should be added with grease regularly. If the grease is not enough

There will be electric brushes in this machine. The parts where the brushes touch each other must be kept clean. The bearings in the machine also need to be checked regularly， the bearing will be seriously worn during operation， affecting the service life of the machine. There are all kinds of wires and cables in the machine. After a period of use， it is necessary to check the wires and cables. If the wires and cables are damaged， they should be repaired or replaced. We should also regularly check whether the screws at the connection are loose. If the screws are loose，Cargo Lift we should tighten them. Some screws must meet certain torque requirements. In the absence of relevant professional equipment，ShaoergotauryangHousehold hydraulic lifting platformConsiderate service we can go to the maintenance shop to use professional equipment to tighten the screws. We must make the screws meet the corresponding torque requirements.

7The lift has strong bearing capacity， and is suitable for two people (can carry certain weight tools and materials) to climb at the same time; Various non-standard products can also be customized according to different environments to meet different needs.

lCasetaThere are three movable plates on both sides of the adjusting plate， which can effectively avoid injuring the toes of the operator when the adjusting plate falls， designated dealers with complete products and quality assurance

The sinking of the cargo elevator is the phenomenon that the table top falls due to gravity after a certain period of time after rising to the specified position. Of course， this problem must be abnormal， so how to solve it? First of all， find out the reason. The following editor summarizes the ultimate solution.

DBoramarThe elevator is now very popular and can easily deliver goods to high buildings. Among them， the hydraulic elevator is more popular with people and people can choose the suitable one according to their actual situation. However， pay attention to the lifting speed of the hydraulic lift when working at ordinary times，Cargo Lift and do not make mistakes. What factors will affect the lifting speed of hydraulic lift?

FzThe lubrication and hydraulic oil of reducer， gearbox， external gear and other parts shall be carried out according to the requirements in the lubrication table.

Keep the access road of external construction elevator smooth and have enough space for parking equipment. When the auxiliary installation of the crane is required， full consideration shall be given to whether the site environment meets the operating conditions of the crane.

It is necessary to check the brake of the guide rail elevator frequently. There should be no dirt on the friction surface.

xThere are three movable plates on both sides of the adjusting plate， which can effectively avoid injuring the toes of the operator when the adjusting plate falls， so as to ensure the safety of the equipment. Long-term promotion of goods elevator manufacturers and other brands of products， designated dealers with complete products and quality assurance

HNormally closed valve and motor are powered on at the same time; The solution is correct wiring. When the motor is powered on， the valve is closed and the power is cut off.

NHigh quality brandThe folding boom elevator is mostly driven by hydraulic mode， and the source of power for the hydraulic system is hydraulic oil. Only when the hydraulic oil is sufficient and the oil quality is high， can the folding boom elevator provide greater torque output，Cargo Lift thus improving the working efficiency. How can we judge whether the newly filled hydraulic oil is sufficient? What is the hydraulic oil quantity standard?

jEAlways check all wires and cables for damage. Products， professional sales elevator manufacturers to ensure the safety of transactions

Connect the motor to the elevator naturally. During connection，ShaoergotauryangHousehold hydraulic lifting platformConsiderate service the concentricity of the elevator output shaft and the motor input shaft must be consistent， and the outer flanges of the two must be parallel. Inconsistent centricity may cause the motor shaft to break or the elevator gear to wear.

Low cost: compared with the scissor-type mobile lifting platform， the cost is much lower so when selecting the lifting platform， consider the use range work frequency， load and other factors of the lifting platform to select the lifting platform suitable for the work requirements.

Quality inspection reportkRegularly check whether all mechanisms operate normally and whether there is noise. If any fault is found， it must be eliminated in time. Long-term sales of elevator manufacturers have not reversed hands to avoid second-hand price difference， and the price is % higher than the market price! More than one ton is more expensive!

RThe aluminum alloy elevator is simple in design， beautiful and practical. It replaces the previous operation mode of scaffold and crane suspension，Hydraulic elevator_ Cargo elevator_ Cargo elevator_ Hydraulic lift - goods lift manufacturer with high efficiency， and low failure rate.

Secondly， there is no dirt on the friction surface. If there is dirt， it needs to be washed off with gasoline or thinner; The lubrication and hydraulic oil of each part of the equipment reducer， external gear， etc. shall be carried out according to the requirements in the lubrication table; Correct maintenance of hydraulic guide rail elevator: regularly check whether the wire rope of each part is broken or loose. If this phenomenon is found， replace it in time. The maintenance of wire rope must be carried out in strict accordance with the specification; Check the connection of each part according to the braking rules and regulations. If there is any looseness， tighten it in time. Check the tightness of the connecting bolts of the equipment when the body is under pressure. All connecting shafts should be equipped with cotter pins; Check whether the operation of each mechanism is normal， whether there are noises and faults according to regulations， and remove all faults in time; When installing， disassembling and adjusting the rotating mechanism of the equipment， it is necessary to pay attention to that the reducer and the gear center line should be parallel， and the meshing clearance should be appropriate; Conduct a comprehensive inspection of the equipment regularly to check whether the wires and cables are damaged， and whether the motor is overheated. Replace it in time to eliminate the fault before continuing to operate; The bearing lubrication of the motor shall be ensured. Each box， distribution box and brush shall be kept clean. The travel switch contact point of each safety device must be safe and reliable.

uCasetaThe anti-rust work of aerial work vehicles is generally something that needs attention when aerial work vehicles have not been used for a long time. How should we protect the body of aerial work vehicles from corrosion? In fact， it is very simple to go to the maintenance station for anti-corrosion， as long as our car owners can use some materials they can find， and pay attention to the driving habits to ensure that the aerial work vehicle does not rust. Here are some points for reference.

aLThe maintenance shall be carried out regularly and by designated personnel on schedule， including half-monthly maintenance， monthly maintenance and annual maintenance. The contents of each type of maintenance are different， but all of them shall be done， with detailed records and signatures of both parties.

Three-pillar aluminum alloy elevator: three groups of mast-supported operating platforms lift synchronously， and the support structure is the same as that of single-mast-type platform， with super load capacity and working stability. The overall lifting guardrail device has good strength， greatly reduces the height of the whole machine during transportation， and is very convenient for loading and unloadingdisassemble.