NeustadtElectric three wheel hydraulic lifting platformScope of application and issues encountered during use

The reason for the slow rise and fall rate of the aluminum alloy lifting platform and the disposal of the equipment and equipment after the purchase and utilization， due to the improper use or aging， and the use of the hydraulic lift to incubate the dirt， the sign of the slow rate occurred. After the speed slows down， hydraulic valve， hydraulic oil pump，Products motor speed regulation assembly，PalermoElectric mobile hydraulic lifting platformWhat are the types of corrosion prevention methods available etc. The following is a brief introduction to the four reasons for the slow speed and the mediation methods.

0The folding boom elevator is mostly driven by hydraulic mode， and the source of power for the hydraulic system is hydraulic oil. Only when the hydraulic oil is sufficient and the oil quality is high， can the folding boom elevator provide greater torque output， thus improving the working efficiency. How can we judge whether the newly filled hydraulic oil is sufficient? What is the hydraulic oil quantity standard?

aNeustadtIt is forbidden to use hemp rope as safety rope when using mobile elevator for aerial work.

With the progress of the times， the guideway elevator is widely used. It is inevitable that some problems will occur when using the guideway elevator. So today， especially the guideway elevator whether used outdoors or indoors， will inevitably have some small problems after a long time. At this time， what we should do is to maintain and maintain the elevator. How to correctly follow the steps has become a difficult problem. Let me explain it to you.

GiThe normally closed valve is dirty; The solution is to remove the normally closed valve and use detergent or cleaning.

Normally closed valve and motor are powered on at the same time; The solution is correct wiring. When the motor is powered on， the valve is closed and the power is cut off.

Make the foundation according to the foundation plan，Products pay attention to the alignment， leveling and alignment， and ensure the level of the foundation and various use requirements.

bSafety device of guide rail hydraulic lifting platform The mechanical part of guide rail hydraulic lifting platform mainly includes hydraulic system and mechanical device.

YAfter the goods are transported， clean the garbage on the platform.

LEncyclopedic knowledgeOnce the goods elevator breaks down， the maintenance unit will arrive at the site within the specified time (the specific time is not minutes according to Beijing regulations).

fDOnce the goods elevator breaks down， the maintenance unit will arrive at the site within the specified time (the specific time is not minutes according to Beijing regulations).

According to the development law of the elevator， there will be a rebound if there is a trough， and if there is a downturn， the policy is the booster of the industrys recovery， which increases the infrastructure construction which provides a great opportunity for the industry; After that is“ The Belt and Road” This is undoubtedly another opportunity for the industry.

For the introduction of daily maintenance of the elevator，Products the brake of each organization should generally inspect and adjust the interval between the brake shoe and the brake wheel to ensure that it is sensitive and reliable. There should be no dirt on the surface. If there is any dirt， it must be washed off with gasoline or thinner.

middlemanuThe oil cylinder seal is not replaced in the oil cylinder of the boarding bridge manufacturer. The lifting table does not lower. The lowering valve fails. When the lowering button is pressed，PalermoElectric mobile hydraulic lifting platformWhat are the types of corrosion prevention methods available check whether the lowering valve is powered on. If there is no electricity， try to eliminate it; If there is power， remove the fault of the lowering valve itself， or replace the lowering valve. The lowering valve should be kept clean and lubricated.

BCheck whether all travel switches are loose. If yes， tighten them. Pay special attention to the ultra-high protection stroke of the hydraulic lifting platform to avoid accidents caused by the equipment exceeding the high safety height; Pin shaft Check whether the pin shaft (ear pin shaft and center pin shaft) is dry. If some are dry， inject corresponding lubricating oil immediately; Check whether nuts， nuts， screws，Hydraulic elevator_ Cargo elevator_ Cargo elevator_ Hydraulic lift - goods lift manufacturer etc. are loose on site， and if so， immediately reinforce them; Ensure that the hydraulic lifting platform lifts smoothly; Outrigger (for aerial work platform)

The scissor-type fixed lifting platform is a kind of transportation and loading equipment for transporting goods from one height to another. After the operation， the platform is level with the ground， which does not occupy the ground space and does not affect the passage.

mNeustadtThe guideway elevator installed outdoors is often exposed to rain and sun， so special attention should be paid to regular maintenance and inspection to avoid accidents. High-priced sales of various specifications of elevator manufacturers timely supply， cost-effective， has become the preferred brand of many wire products， welcome to buy!

sYIn todays society，“ Brand” It is an intangible asset. As long as a product has a brand， it will have a certain popularity， cohesion and diffusion.

The above is Xiaobians analysis of the slow speed of the guideway elevator in the application. I hope it can help you. If there are problems check them one by one， and solve them in time. Aluminum alloy elevator is a large machine that can be seen everywhere in our life. But there are always many problems in the use process. Today， Xiaobian will talk about the reason and treatment of the slow speed of the aluminum alloy lifting platform.