QinhuangdaoElectric hydraulic platform lift truckHow is the production status

In case of overheating of the motor during the daily maintenance of the elevator， park the car immediately， remove the obstacles， and then continue to run. The motor bearing should be smooth and excellent.

8Different power modes can be selected according to different requirements such as three-phase AC power supply， single-phase AC power supply， DC power supply and internal combustion power supply. With manual hydraulic equipment，Elevator goods ladder the lifting operation can be carried out in places with power failure or without power supply，BordeauxElectric hydraulic lifting platformNew breakthroughs in product exports and components can be added. When the platform length is short， and then the operation power can be increased. It is the necessary equipment product of modern huge construction and equipment， and it is necessary for safe and civilized production at high altitude.

oQinhuangdaoThe main categories of aluminum alloy lifts in the Chinese market are based on the structural form of aluminum alloy lifts. The aluminum alloy lifting platform can be divided into the following categories: single-column aluminum alloy lifting platform， which is light and small， flexible in movement， generally less than meters high， and generally less than kilograms in load， especially suitable for one-person operation.

Check the circuit breaker and motor wiring.

ONick binfarstCurved-arm elevator: the lifting equipment used for aerial work can cross obstacles to carry out aerial work. When the platform is lifted to any position， it can walk and work at the same time. It has compact structure and flexible steering. The width of its site can ensure that the equipment can enter narrow passages and crowded working areas. The standby power unit can be operated to reset the working platform and can be towed to any place as a convenient means of transportation.

HkAfter the goods are transported，Elevator goods ladder clean the garbage on the platform.

Nowadays， small and medium-sized enterprises buy products with the idea of good quality and favorable price. Specializing in elevator manufacturers， old brands， price advantages quality assurance!

Preparation before folding and installation of the elevator Preparation before folding and installation of the elevator Carefully prepare the special construction plan for installation and constructionThe fence and hanging cage shall clean the foundation surface and install the anchor bolts. If the installed construction elevator is installed on the basement floor， measure the perpendicularity of the guide rail frame with a theodolite a pad iron must be used under the screw to increase the bearing surface between the nut and the floor to reduce the friction between the nut and the floor; Insert steel plate shims of different thickness between the chassis and the foundation stone at the anchor bolt to adjust the perpendicularity of the guide rail frame; Install three standard sections， ensure the perpendicularity of each main pipe of the guide rail frame in two directions， and press the four anchor bolts after the guide rail frame is adjusted to be vertical; Adjust the perpendicularity of the fence door frame as above， and press the rest of the anchor bolts; Install the buffer spring; Connect the fence of the other half with the front half with bolts; As above， adjust the verticality and press the anchor bolt， and release the brake on the motor in the cage. (For SC/ type，Elevator goods ladder and products similar to the current vehicle-mounted aerial work platform began to be used for fruit picking， branch construction，BordeauxElectric hydraulic lifting platformNew breakthroughs in product exports the concentricity of the elevator output shaft and the motor input shaft must be consistent， and the outer flanges of the two must be parallel. Inconsistent centricity may cause the motor shaft to break or the elevator gear to wear.

UbuildThe lift lease meets the tensile strength; Half of the elevator cables are used for extension. High-rise elevators can reach more than meters， and the dead weight of the -meter cable is nearly kilograms， so the cable must have sufficient tensile strength. At present， there are self-supporting flat composite elevator monitoring special cables on the market. This kind of cable combines video coaxial cable， power cable， data cable and steel strand to form a flat ribbon cable. In this way， the tension of the whole cable is borne by the steel wire rope，Hydraulic elevator_ Cargo elevator_ Cargo elevator_ Hydraulic lift - goods lift manufacturer and the tensile strength is very good. It will not break the signal cable due to gravity during elevator operation.

mRThere will be electric brushes in this machine. The parts where the brushes touch each other must be kept clean. The bearings in the machine also need to be checked regularly， especially the bearings should be added with grease regularly. If the grease is not enough， the bearing will be seriously worn during operation， affecting the service life of the machine. There are all kinds of wires and cables in the machine. After a period of use， it is necessary to check the wires and cables. If the wires and cables are damaged， they should be repaired or replaced. We should also regularly check whether the screws at the connection are loose. If the screws are loose， we should tighten them. Some screws must meet certain torque requirements. In the absence of relevant professional equipment， we can go to the maintenance shop to use professional equipment to tighten the screws. We must make the screws meet the corresponding torque requirements.

The detailed reason why the hydraulic station cannot be washed with water is that if it is done， it will corrode the oil tank in the hydraulic station， and once water is mixed in the hydraulic station， the damage to the hydraulic system is very large. Therefore， it will simply form pipeline corrosion and water vaporization， which will cause adverse effects or results. Therefore， it is necessary to prevent this to ensure the normal operation of the hydraulic station and its service life.

When installing， disassembling and adjusting the slewing mechanism， pay attention to ensure that the center line of the slewing mechanism reducer is parallel to the center line of the gear， its meshing surface is not less than %， and the meshing clearance is appropriate.

Welcome calls cPay attention to check whether each wire rope has broken wires and loose strands. If it exceeds the relevant regulations， it must be replaced immediately. The maintenance of wire rope shall be in strict accordance with the provisions of .

UThe daily maintenance of the guide rail elevator should ensure that the transmission position where the grease nipple is located needs to be greased twice a month. For the parts that cannot be greased， it is necessary to dredge the oil circuit or replace the grease nipple until the grease can be added， the lift manufacturer should first make the motor shaft keyway perpendicular to the tightening bolt. To ensure uniform stress， please screw on the mounting bolts at any diagonal position， but do not tighten them. Then screw on the mounting bolts at the other two diagonal positions， and then tighten the four mounting bolts one by one. After that， tighten the tightening bolts. All tightening bolts shall be fixed and checked with torque wrench according to the indicated fixed torque data. Lifts and lifting platforms are widely used special equipment for aerial work. Its scissor-type mechanical layout makes the lift have high stability after lifting， and the wide range of operation and high bearing capacity make the scale of aerial work more and more large， and support multiple people to work together. It makes aerial work more powerful and safer. It is a widely used special equipment for aerial work.

iQinhuangdaoThe boxes and distribution boxes of the hydraulic lift shall be kept clean and the dust on the electrical equipment shall be cleaned in time.

zUThe lifting of the rated speed and rated load of the guideway elevator means that the power of the main machine must be increased and a larger traction machine must be used. Once the power of the main engine increases， the power of the frequency converter must also increase and the corresponding contactors and power lines must be enlarged.

In case of overheating of the motor during the daily maintenance of the elevator， park the car immediately， remove the obstacles， and then continue to run. The motor bearing should be smooth and excellent.