+8613064022215
sellelevator@163.com
Aerial work is also very common now， and the elevator is also very popular in the market. Many high-rise transportation works are completed by elevators， which are efficient and safe. However， pay attention to the installation of the elevator， otherwise there will be problems. Nobody wants to see this happen. What are the installation precautions for the elevator?
8Low cost: compared with the scissor-type mobile lifting platform， the cost is much lower，Hydraulic elevator so when selecting the lifting platform，SiroliFoot hydraulic platform lift truckExport Situation Analysis Report consider the use range， work frequency， load and other factors of the lifting platform to select the lifting platform suitable for the work requirements.
rSong BotaiWhat is the pressure of the lifting platform? The movement of the lifting platform has always been our concern. Our use occasions are uncertain， and most of them are part-time workers. So in order to better attract customers， we are constantly studying the mobile lifting platform， which can be used in different occasions. However， for some large logistics companies or some enterprise processing plants， we are still used to using fixed elevators， It has a huge load capacity and strong stability，Hydraulic elevator which can meet the needs of many customers. This is also the use of domestic lifting platforms in recent years.
At present， the aluminum alloy elevator has a wide range of outstanding functions. Chinas aluminum alloy elevator has been imported and exported abroad， accounting for a certain proportion in the world. Because of its practicality and wide use， time and cost， which is in line with the use of modern people.
AMansa : Chemical derusting is mainly a kind of derusting that uses acid to react with the metal parts of the screw lift to remove the rust products on the rust surface of the push rod. This kind of derusting is mainly used for the screw lift of large machinery. At the same time， it was found that it was mainly caused by two reasons: the loss of hydraulic pressure and the leakage of hydraulic valve or seal.
To check the ground of the correct construction elevator first of all， we should check the foundation to see if there is water accumulation and whether the grounding system meets the requirements. We also need to see how the structural bolts of the frame are fastened and whether there are cracks in the weld. We should set it according to the instructions. In mechanical transmission， it can be divided into open type and closed type. Of course， there are many safety equipment for the elevator.
Anti-corrosion treatment of the paint layer of the elevator how to correctly install the linear guide rail movement is used to support and guide the moving parts to make reciprocating linear movement according to the given direction. The linear guide rail itself has no power drive device. The function of the linear guide rail is to guide the equipment to and fro within a fixed linear range， and to carry the equipment. The movement of the slider on the guide rail needs another drive device，Hydraulic elevator manyOf course， it can also be used with other drive devices.
iIn our daily life today，SiroliFoot hydraulic platform lift truckExport Situation Analysis Report the hydraulic cargo elevator is also more and more widely used and deeply loved by customers. As a lifting power tool， the maintenance of the cargo elevator must not be careless. The following is a brief introduction to the daily maintenance of the hydraulic cargo elevator.
HHigh-altitude operation is a very common thing now， but it also has a certain risk factor. So people invented the hydraulic lifting platform， which is more convenient to help people complete aerial work. However， people should also pay attention when using the hydraulic lifting platform， otherwise it is easy to break down， clean the garbage on the platform.
zWPay attention to check whether each wire rope has broken wires and loose strands. If it exceeds the relevant regulations， it must be replaced immediately. The maintenance of wire rope shall be in strict accordance with the provisions of .
Always check all wires and cables for damage. Products，Hydraulic elevator_ Cargo elevator_ Cargo elevator_ Hydraulic lift - goods lift manufacturer tens of millions of products at your choice， professional sales elevator manufacturers to ensure the safety of transactions
If the hydraulic valve is damaged， its effectiveness shall be maintained. If it is damaged， it can be replaced in time. For a long time， the reasonable price and perfect service of all kinds of elevator manufacturers have been recognized by customers
packingpSome office buildings and hospitals may need several or even dozens of passenger lifts. In order to increase the speed， efficiency and area of the electric lift most high-rise buildings will divide the electric lift into an array， each group is responsible for some floors， and make different adjustments and scheduling according to the use mode of different floors at different times.
YSystem: explosion-proof electric control system， remote control system， PIC system. The manufacturer specialized in the sales of elevator has stable， safe， reliable and maintenance-free performance. Its technical level has reached the domestic level and the advanced level of similar products in the world
The damaged part of the elevator that needs to be bandaged and replaced in a timely manner is a kind of hydraulic elevator， also known as guide rail hydraulic elevator， which is applicable to the transportation of goods higher than buildings， restaurants and hotel floors. Here is Lipson Machinery to introduce the daily maintenance of the elevator.
sSong BotaiWhen the distribution box is used， the electric leakage switch shall meet the requirements of the construction elevator. If the fixed elevator installed is frequency conversion， the leakage switch shall be matched with the frequency converter.
eKUsually check whether the organizations operate normally and whether there is any noise. If any obstacle is found， and the brush pressure shall be adjusted to make the contact area not less than %